国民彩票开户

当前位置: 国民彩票开户 > 新闻资讯 > 行业动态 > 正文

电焊钢筋网片铺设前要注意哪些问题?

添加时间:2020-01-02      发布人:http://iemhk.com

  焊丝网又称焊丝网、钢焊接网、钢焊接网、钢焊接网、焊丝片。是纵向和横向的钢筋按一定的距离和直角布置,所有的交点都焊接在一起。你知道钢网焊接前应注意什么问题吗?
  Wire mesh is also known as wire mesh, steel welding mesh, steel welding mesh, steel welding mesh and wire piece. The longitudinal and transverse reinforcement are arranged at a certain distance and right angle, and all intersections are welded together. Do you know what should be paid attention to before steel mesh welding?
  当焊接钢丝网粗糙焊接网不能曲折,焊接1 - 2钢筋焊接网的少,然后两个梁,和直接采用网站绑定方法,弥补减少横向钢筋,附加钢筋焊接网连接的每个节点应选择线绑定。在两个焊接网的两端之间,钢筋搭接处的更小搭接长度不得小于更小锚固长度la的1.3倍。
  When the welded steel wire mesh rough welded mesh can not be zigzag, and the last welded 1 - 2 reinforcement welded mesh is less, then two beams, and directly use the website binding method to make up for the reduction of transverse reinforcement, each node connected by the additional reinforcement welded mesh shall be bound by a line. Between both ends of the two welded nets, the minimum lap length of the steel bar lap shall not be less than 1.3 times of the minimum anchorage length la.
  搭接区域内两个焊接钢网片有一非横向配筋时,加肋焊接钢网片更小搭接长度为更小锚固长度la的1.3倍,且不小于300 mm。搭接区域纵向受力钢筋直径d≥10mm时,应增加搭接长度5d使用。
  When two welded steel meshes in the overlapping area have one non transverse reinforcement, the minimum overlapping length of the welded steel mesh with ribs is 1.3 times of the minimum anchoring length La, and is not less than 300 mm. When the diameter of the longitudinal stressed reinforcement in the overlapping area D ≥ 10 mm, the overlapping length shall be increased for 5 days.
济南钢筋批发
  焊接钢筋网片底部网络选择螺柱位置和垫放置两种方式,双向竹节钢筋焊接钢筋网的面纱,宜选用方法的搭接接头应设置在压力相对较小,应设置从梁季度净截面,搭接长度不应小于30 dd圈方向,强化和直径不应小于250毫米。
  Two methods are selected for the bottom network of welded steel mesh: stud location and pad placement. For the veil of welded steel mesh of two-way bamboo bar, the lap joint of the appropriate method should be set at a relatively small pressure, and the net section should be set from the beam quarter. The lap length should not be less than 30 DD circle direction, and the reinforcement and diameter should not be less than 250 mm.
  那么,在钢网的焊接铺设中应该注意今天大家要完成哪些问题。焊接钢筋网片铺设前,应先拟定焊接钢筋网片安装方案,焊接钢筋网片铺设,根据现场实际及设备人员现场服务进行铺设指导,以尽量减少焊接钢筋网片铺设时的麻烦。
  So, in the welding and laying of steel mesh, we should pay attention to what problems we need to complete today. Before the laying of welded steel mesh, the installation scheme of welded steel mesh shall be proposed first, and the laying of welded steel mesh shall be guided according to the actual situation on site and the field service of equipment professionals, so as to minimize the trouble during the laying of welded steel mesh.
上一条: 钢筋在桥梁加固中的作用是什么?
下一条: 最后一页
咨询热线: 13605413762